The PCN3TJ00F from Sharp is a 4 pin, mini flat general purpose photocoupler. This photocoupler contains an IRED optically coupled to a phototransistor. Tel: Fax: / http://www. Photocoupler. Product Data Sheet. LTVT. Spec No. A/PG Page 2 of 8. Mini-flat Package General Purpose Photo Couple. KPCNT. Absolute Maximum Ratings (Ta=25 °C).
|Published (Last):||22 May 2006|
|PDF File Size:||9.36 Mb|
|ePub File Size:||9.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
What if there is photo-Triac instead of Photo-transistor, How to test then?
You agree that the Information as provided here through an intermediary may not be error-free, accurate or up-to-date and that it is not advice. Mihai on February 2, at 5: Nupra on Phogocoupler 18, at 6: If the input is at 2V DC, then the output resistance should be around — ohms.
There pjotocoupler no law governing all things. Some features may not work properly. The alcohol never solved anything, but neither did water or milk. Thank you for your feedback. I have two circuits.
In my example an ohmmeter is connected at the output, in order to see the change in resistance.
It depends on the 2nd circuit you are supplying the voltage on collector of the optocoupler, optocoupler will never transfer the voltages photocokpler circuit1 to circuit2, it decreases resistance between your supplied voltages at collector and emitter on the input of circuit2.
This site uses Akismet to reduce spam. Kannan E on July 19, at 9: Please select an existing parts list. If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the LED between pins 3 and 4 the emitter and collectorand you should get a high resistance value both ways if the phototransistor is good.
Pohtocoupler this item to a new parts list.
The purpose of an optocoupler is to transfer signals from one circuit to another yet keep them galvanically isolated. The Manufacturers and RS disclaim all warranties including implied warranties of merchantability or fitness for a particular purpose and are not liable for any damages arising from your use of or your inability to use the Information downloaded from this website.
Buy Optocouplers with 4-Pin Pins | eBay
Please enter a message. Did you reffer to isolation resistance when you mention some phototransistors have high resistance? Please correct the pin numbers in image.
For response time or frequency response data, check the datasheet. Emprical method you mention above or the testing circuit on the datasheet of H11B1? Mihai on July 16, at 5: Mihai on Phhotocoupler 27, at By clicking the accept button below, you agree to the following terms.
Photocoupler 1-CH Transistor Mini-Flat
Thank you for your feedback. The Manufacturers disclaim all warranties including implied warranties of merchantability or fitness for a particular purpose and are not liable for any damages arising from your use of or your inability to use the Information downloaded from this website. The foregoing information relates to product sold on, or after, the date shown below.
Shahid on August 7, at 1: Siroos on October 14, at First of all thanks for sharing such an useful information. Here is the web site. How the optocoupler Type SFH acts when the positive line is open. The foregoing information relates to product sold on, or after, the date shown below. Wade on February 5, at 9: How can i test them?
I use analog ohmmeter with 2 internal batteries, 3V to turn on LED pins 1 and 2and digital V-metar on diode tester mode on transistor side. Save to an existing parts list Save to a new parts list. Arvind Vijaykumar on June 1, at You agree that the Information as provided here by RS may not be error-free, accurate or up-to-date and that it is not advice. Thanks for the easy to follow explanation of how to rest an optocoupler. Your email address will not be published.
PCNJF Sharp | Photocoupler 1-CH Transistor Mini-Flat | | RS Components
I was wondering if i could just bypass the optcoupler and see if it works. The nice thing about standards is that you have so many to choose from. The optocoupler is FL C F, should i just join the emittor and collector pins? I hope it helps. The Manufacturers reserve the right to change this Information at any time without notice.
Step 2 If the LED is good then we should check the phototransistor, you could measure it with the ohmmeter just like the LED between photocopler 3 and 4 the emitter and collectorand you should get a high resistance value both ways if the phototransistor is good.